• MULTI-GEL is a solvent-free, non-toxic, single-component water-reactive polyurethane injection resin. It reacts with water to form a flexible hydrophilic barrier. Depending on the amount of water in the mixture and when cured, MULTI-GEL will vary in consistency from strong elastic rubber-like foams, to stable gels containing as much as 800% water. After curing, MULTI-GEL absorbs limited amounts of water and will shrink slowly if allowed to dry.

    ADVANTAGES

    • In the range of 1:1 to 2:1 water:resin ratios, hydrophilic foams with decreasing strength are obtained in less than one minute

    • In the range of 2:1 to 8:1 water:resin ratios, hydrophilic gels are obtained in less than one minute

    • When cured, deflects excessive water away from penetrating into a structure

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheet

    RECOMMENDED PRODUCTS

    PUMP CLEANER

    PUMP CLEANER is a clear colourless liquid solution that is used to flush resin residuals from one and two component chemical grout pumps.

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

  • RIGID GROUT is a low-viscosity dual-component polyurethane grout. It is used to stabilize water-bearing soils and fill open voids.

    RIGID A and RIGID B are combined to produce a strong, hard foam that expands to approximately 10 times its original volume.

    ADVANTAGES

    • Expansive, rigid foam provides structural support

    • Develops adhesive bond that adheres to loose substrates

    • Fast foaming and curing permits efficient installation

    • Solvent-free and non-toxic

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheets

    RIGID GROUT A

    RIGID GROUT B

    RECOMMENDED PRODUCTS

    PUMP CLEANER

    PUMP CLEANER is a clear colourless liquid solution that is used to flush resin residuals from one and two component chemical grout pumps.

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

  • CRACK FLUSHING AGENT is a concentrated, solvent-free, non-toxic solution that is diluted on site and used to clean cracks and construction joints in concrete structures prior to injection of polyurethane resins.

    CRACK FLUSHING AGENT, after dilution to 5% concentration, is used for the cleaning and preparing of wet, damp or dry cracks and construction joints in all types of concrete structures including storage tanks, hydro dams and tunnel linings.

    ADVANTAGES

    • Inorganic mineral solution, manufactured from ingredients meeting NSF criterion for use in contact with potable water

    • Non-flammable

    • Solvent-free, non-toxic

    • Complies with Food Chemical Codex Specifications

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheet

    RECOMMENDED PRODUCTS

    PUMP CLEANER

    PUMP CLEANER is a clear colourless liquid solution that is used to flush resin residuals from one and two component chemical grout pumps.

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

    Chemical Injection in Underground Parking Garage

  • MME UNIVERSAL RESIN is a low-viscosity polyurethane resin designed for single-component injection. It penetrates fine cracks in rock and concrete,  and reacts with water to form a semi-rigid hydrophobic foam barrier. Once cured, the hydrophobic seal repels water, will not shrink or expand, and serves as a long-term solution to water infiltration.

    ADVANTAGES

    • Suitable for use near potable water

    • Stops high-pressure inflows

    • Will not shrink or expand after curing

    • Controlled reaction time by varying the acelerator dosage

    • Resistant to corrosive environments and temperature fluctuations

    • Solvent-free and non-toxic

    WQA Seal

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheet

    RECOMMENDED PRODUCTS

    MME UNIVERSAL ACCELERATOR

    Select appropriate MME UNIVERSAL ACCELERATOR ratio and verify that the resulting cure time conforms to project specifications. Use as low as 1% for slow reaction time or as much as 10% for fast reaction time.

    Safety Data Sheet

    PUMP CLEANER

    PUMP CLEANER is a clear colourless liquid solution that is used to flush resin residuals from one and two component chemical grout pumps.

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

    Innovative Water Cut Off Solution for a Hard Rock Tunnel

  • MME Multiurethanes CIMENT FONDU consists mainly of calcium aluminates (CaO & Al2O3) and other minor ingredients. This product is typically used in refractory applications where high-temperature resistance is required, as well as applications that require corrosion resistance.

    For mining and heavy civil grouting applications, it is used in conjunction with Type GU, Type HE and other similar cements for setting drill casings or other specific applications where rapid strength development is required to reduce delay time before re-drilling can proceed.

    By comparison, cement Types GU and HE consist mainly of calcium silicates (CaO & SiO2) and other minor ingredients and typically take several hours to cure to a hardened state.

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

  • MME FLEXIBLE RESIN is a low-viscosity polyurethane resin designed for single-component injection. It penetrates fine cracks and reacts with water to form a flexible hydrophobic foam barrier that stops flowing leaks and seepages. It is suitable for use near potable water. Once cured, the hydrophobic seal repels water, will not shrink or expand, and serves as a long-term solution to water infiltration in concrete structures.

    ADVANTAGES

    • Retains strength, size, and flexibility

    • Controlled reaction time by varying the accelerator dosage

    • Resistant to corrosive environments and temperature fluctuations

    • Solvent-free and non-toxic

    WQA Seal

    DOWNLOAD TECHNICAL LITERATURE

    Product Data Sheet

    Safety Data Sheet

    RECOMMENDED PRODUCTS

    MME FLEXIBLE ACCELERATOR

    Select appropriate MME FLEXIBLE ACCELERATOR ratio and verify that the resulting cure time conforms to project specifications. A typical accelerator dosage is 2% for most concrete crack injection work; use as low as 1% for slow reaction time or as much as 10% for fast reaction time.

    Safety Data Sheet

    PUMP CLEANER

    PUMP CLEANER is a clear colourless liquid solution that is used to flush resin residuals from one and two component chemical grout pumps.

    Product Data Sheet

    Safety Data Sheet

    FEATURED PROJECT

    Chemical Injection in Underground Parking Garage

Go to Top